華為交換機怎麼配置vrid
A. 如何連接華為交換機進行配置
新設備應該有配置線，之間接上console ，一頭連電腦，就可以通過點擊開始，然後點擊附件，然後點擊通訊，看到超級終端，進行默認設置，即可進入交換機配置界面，配置好交換機後，將電腦設置好固定IP即可進行TELNET 遠程連接配置
B. 華為交換機典型配置，請給出詳細步驟和說明
交換初始化方法：
1、通過CONTROL口連接交換機，使用SecureCRTPortable軟體連接，打開軟體後選擇「新建會話」，在對話框中選擇「Serial」選項，點擊下一步，波特率9600，埠以實際使用的埠為准，不要選中RTS/CTS，否則鍵盤不能使用。
2、連接交換機。
3、進入交換機後，輸入
reset saved-configuration
命令運行後，輸入
reboot
在第一個提示（是否保存），輸入N，不保存。
接著在提示是否重啟中輸入Y，回車後交換機自動重啟。
重啟完成後，可開始執行交換基礎配置了。
1、配置設備名稱
system-view進入系統視圖
sysname HeXin命名為「HeXin」
2、配置管理VLAN
[HeXin]vlan 1進入VLAN 1
[HeXin-vlan1]description admin_VLAN設置VLAN 1為管理VLAN
3、配置HeXin與匯聚交換的連接埠為trunk
[HeXin]interface Gigabitethernet 0/0/1進入埠G速埠1
[HeXin-GigabitEthernet0/0/1]port link-type trunk配置埠1為trunk口
[HeXin-GigabitEthernet0/0/1]port trunk allow-pass vlan 1配置允許從埠1通行的VLAN為VLAN 1，如果想讓所有的VLAN都可以通過埠1，可執行命令port trunk allow-pass vlan all
[HeXin-GigabitEthernet0/0/1]quit退出埠1
4、配置交換機的管理IP
[HeXin]interface vlanif 1
[HeXin-Vlanif1]ip 10.10.10.1 255.255.255.0管理IP地址為10.10.10.1，網關255.255.255.0
[HeXin-Vla
C. cisco交換機vrrp應該怎麼配置
VRRP和Vlan關聯就行了。交換機必須三層。
D. 華為交換機怎麼配置
華為交換機常用命令：1、display current-configuration 顯示當前配置2、display interface GigabitEthernet 1/1/4 顯示介面信息3、display packet-filter interface GigabitEthernet 1/1/4 顯示介面acl應用信息4、display acl all 顯示所有acl設置 3900系列交換機5、display acl config all 顯示所有acl設置 6500系列交換機6、display arp 10.78.4.1 顯示該ip地址的mac地址，所接交換機的埠位置7、display cpu顯示cpu信息8、system-view 進入系統圖（配置交換機），等於config t 命令9、acl number 5000 在system-view命令後使用，進入acl配置狀態10、rule 0 deny 0806 ffff 24 0a4e0401 f 40 在上面的命令後使用，，acl 配置例子11、rule 1 permit 0806 ffff 24 000fe218ded7 f 34 //在上面的命令後使用，acl配置例子12、interface GigabitEthernet 1/0/9 //在system-view命令後使用，進入介面配置狀態13、[86ZX-S6503-GigabitEthernet1/0/9]qos //在上面的命令後使用，進入介面qos配置14、[86ZX-S6503-qosb-GigabitEthernet1/0/9]packet-filter inbound user-group 5000 //在上面的命令後使用，在介面上應用進站的acl15、[Build4-2_S3928TP-GigabitEthernet1/1/4]packet-filter outbound user-group 5001 //在介面上應用出站的acl16、undo acl number 5000 //取消acl number 5000 的設置17、ip route-static 0.0.0.0 0.0.0.0 10.78.1.1 preference 60 //設置路由18、reset counters interface Ethernet 1/0/14 //重置介面信息19、save //保存設置20、quit //退出（此信息僅為分享之用，我們不排除對您並不適用的可能。另，如此信息侵犯您的權益，請告知我們，我們會及時刪除）
E. 華為交換機怎麼配置
其實交換機的配置方法也不難，下面只介紹進入配置界面的方法，至於如何配置交換機的詳細步驟那是比較多的，要視具體情況而定，不作具體介紹。
進入交換機配置界面步驟很簡單，只需簡單的兩步：第1步：單擊"開始"按鈕選擇"運行"菜單項，然後在對話框中按"telnet 61.159.62.182"格式輸入。
登錄（當然也可先不輸入IP地址，在進入telnet主界面後再進行連接，但是這樣會多了一步，直接在後面輸入要連接的IP的地址更好些），如圖所示。如果為交換機配置名稱了，則也可以直接在"Telnet"。
命令後面空一個空格後輸入交換機配置的名稱。
F. 如何利用華為交換機實現DHCP+VRRP+MSTP
1、核心路由配置
<HXR>dis cu
#
sysname HXR
#
undo info-center enable
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password cipher Fq2|@at%N!ajUn1vMEIBN#7#
local-user admin service-type http
#
firewall zone Local
priority 16
#
interface Ethernet0/0/0
ip address 202.102.224.4 255.255.255.0 ##模擬公網IP地址
#
interface Ethernet0/0/1
description WAN
#
interface Serial0/0/0
link-protocol ppp
#
interface Serial0/0/1
link-protocol ppp
#
interface Serial0/0/2
link-protocol ppp
#
interface Serial0/0/3
link-protocol ppp
#
interface GigabitEthernet0/0/0
#
interface GigabitEthernet0/0/1 ##連接HXA
ip address 10.0.0.1 255.255.255.0
#
interface GigabitEthernet0/0/2 ####連接HXB
ip address 10.0.1.1 255.255.255.0
#
interface GigabitEthernet0/0/3
#
wlan
#
interface NULL0
#
ip route-static 172.16.2.0 255.255.255.0 10.0.0.2 ##回還路由
ip route-static 172.16.2.0 255.255.255.0 10.0.1.2 ##回還路由
#
user-interface con 0
user-interface vty 0 4
user-interface vty 16 20
#
return
<HXR>
2、HXA（核心交換機A的配置）
HXA>dis cu
#
sysname HXA
#
undo info-center enable
#
vlan batch 2 to 5 100
#
stp instance 0 root primary ##MSTP的配置
stp instance 1 root secondary ##MSTP的配置
#
cluster enable
ntdp enable
ndp enable
#
drop illegal-mac alarm
#
dhcp enable
#
dhcp server database enable
#
diffserv domain default
#
stp region-configuration ##MSTP的配置
instance 1 vlan 4 to 5
active region-configuration
#
drop-profile default
#
vlan 100
description hulian
#DHCP配置
ip pool vlan2
gateway-list 172.16.2.1
network 172.16.2.0 mask 255.255.255.0
excluded-ip-address 172.16.2.254
#
ip pool vlan3
gateway-list 172.16.3.1
network 172.16.3.0 mask 255.255.255.0
excluded-ip-address 172.16.3.254
#
ip pool vlan4
gateway-list 172.16.4.1
network 172.16.4.0 mask 255.255.255.0
excluded-ip-address 172.16.4.254
#
ip pool vlan5
gateway-list 172.16.5.1
network 172.16.5.0 mask 255.255.255.0
excluded-ip-address 172.16.5.254
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password simple admin
local-user admin service-type http
#
interface Vlanif1
#
interface Vlanif2
ip address 172.16.2.254 255.255.255.0
vrrp vrid 1 virtual-ip 172.16.2.1
vrrp vrid 1 priority 200
dhcp select global
#
interface Vlanif3
ip address 172.16.3.254 255.255.255.0
vrrp vrid 2 virtual-ip 172.16.3.1
vrrp vrid 2 priority 200
dhcp select global
#
interface Vlanif4
ip address 172.16.4.254 255.255.255.0
vrrp vrid 3 virtual-ip 172.16.4.1
dhcp select global
#
interface Vlanif5
ip address 172.16.5.254 255.255.255.0
vrrp vrid 4 virtual-ip 172.16.5.1
dhcp select global
#
interface Vlanif100 ##兩核心的心跳VLAN IP地址
ip address 10.0.0.2 255.255.255.0
#
interface MEth0/0/1
#
interface Eth-Trunk0 ##創建埠匯聚
port link-type trunk
port trunk allow-pass vlan 2 to 4094
#
interface GigabitEthernet0/0/1
port link-type access
port default vlan 100
#
interface GigabitEthernet0/0/2
port link-type access
#
interface GigabitEthernet0/0/3
#
interface GigabitEthernet0/0/4
#
interface GigabitEthernet0/0/5
#
interface GigabitEthernet0/0/6
#
interface GigabitEthernet0/0/7
#
interface GigabitEthernet0/0/8
#
interface GigabitEthernet0/0/9
#
interface GigabitEthernet0/0/10
#
interface GigabitEthernet0/0/11
#
interface GigabitEthernet0/0/12
#
interface GigabitEthernet0/0/13
#
interface GigabitEthernet0/0/14
#
interface GigabitEthernet0/0/15
#
interface GigabitEthernet0/0/16
#
interface GigabitEthernet0/0/17
#
interface GigabitEthernet0/0/18
#
interface GigabitEthernet0/0/19
#
interface GigabitEthernet0/0/20
#
interface GigabitEthernet0/0/21 ##與接入交換機相連
port link-type trunk
port trunk allow-pass vlan 2 to 4094
#
interface GigabitEthernet0/0/22##與接入交換機相連
port link-type trunk
port trunk allow-pass vlan 2 to 4094
#
interface GigabitEthernet0/0/23##心跳埠
eth-trunk 0
#
interface GigabitEthernet0/0/24##心跳埠
eth-trunk 0
#
interface NULL0
#
ip route-static 0.0.0.0 0.0.0.0 10.0.0.1
ip route-static 0.0.0.0 0.0.0.0 10.0.1.1
#
user-interface con 0
user-interface vty 0 4
#
return
<HXA>
3、HXB（核心B的配置）
<HXB>dis cu
#
sysname HXB
#
undo info-center enable
#
vlan batch 2 to 5 101
#
stp instance 0 root secondary
stp instance 1 root primary
#
cluster enable
ntdp enable
ndp enable
#
drop illegal-mac alarm
#
dhcp enable
#
dhcp server database enable
#
diffserv domain default
#
drop-profile default
#
vlan 101
description hulian
#
ip pool vlan2
gateway-list 172.16.2.1
network 172.16.2.0 mask 255.255.255.0
excluded-ip-address 172.16.2.254
#
ip pool vlan3
gateway-list 172.16.3.1
network 172.16.3.0 mask 255.255.255.0
excluded-ip-address 172.16.3.254
#
ip pool vlan4
gateway-list 172.16.4.1
network 172.16.4.0 mask 255.255.255.0
excluded-ip-address 172.16.4.254
#
ip pool vlan5
gateway-list 172.16.5.1
network 172.16.5.0 mask 255.255.255.0
excluded-ip-address 172.16.5.254
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password simple admin
local-user admin service-type http
#
interface Vlanif1
#
interface Vlanif2
ip address 172.16.2.253 255.255.255.0
vrrp vrid 1 virtual-ip 172.16.2.1
dhcp select global
#
interface Vlanif3
ip address 172.16.3.253 255.255.255.0
vrrp vrid 2 virtual-ip 172.16.3.1
dhcp select global
#
interface Vlanif4
ip address 172.16.4.253 255.255.255.0
vrrp vrid 3 virtual-ip 172.16.4.1
vrrp vrid 3 priority 200
dhcp select global
#
interface Vlanif5
ip address 172.16.5.253 255.255.255.0
vrrp vrid 4 virtual-ip 172.16.5.1
vrrp vrid 4 priority 200
dhcp select global
#
interface Vlanif101
ip address 10.0.1.2 255.255.255.0
#
interface MEth0/0/1
#
interface Eth-Trunk0
port link-type trunk
port trunk allow-pass vlan 2 to 4094
#
interface GigabitEthernet0/0/1
#
interface GigabitEthernet0/0/2
port link-type access
port default vlan 101
#
interface GigabitEthernet0/0/3
#
interface GigabitEthernet0/0/4
#
interface GigabitEthernet0/0/5
#
interface GigabitEthernet0/0/6
#
interface GigabitEthernet0/0/7
#
interface GigabitEthernet0/0/8
#
interface GigabitEthernet0/0/9
#
interface GigabitEthernet0/0/10
#
interface GigabitEthernet0/0/11
#
interface GigabitEthernet0/0/12
#
interface GigabitEthernet0/0/13
#
interface GigabitEthernet0/0/14
#
interface GigabitEthernet0/0/15
#
interface GigabitEthernet0/0/16
#
interface GigabitEthernet0/0/17
#
interface GigabitEthernet0/0/18
#
interface GigabitEthernet0/0/19
#
interface GigabitEthernet0/0/20
#
interface GigabitEthernet0/0/21
port link-type trunk
port trunk allow-pass vlan 2 to 4094
#
interface GigabitEthernet0/0/22
port link-type trunk
port trunk allow-pass vlan 2 to 4094
#
interface GigabitEthernet0/0/23
eth-trunk 0
#
interface GigabitEthernet0/0/24
eth-trunk 0
#
interface NULL0
#
ip route-static 0.0.0.0 0.0.0.0 10.0.1.1
ip route-static 0.0.0.0 0.0.0.0 10.0.0.1
#
user-interface con 0
user-interface vty 0 4
#
return
<HXB>
4、JR01（接入交換機01的配置）
<JR01>dis cu
#
sysname JR01
#
undo info-center enable
#
vlan batch 2 to 5
#
cluster enable
ntdp enable
ndp enable
#
drop illegal-mac alarm
#
diffserv domain default
#
drop-profile default
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password simple admin
local-user admin service-type http
#
interface Vlanif1
#
interface MEth0/0/1
#
interface Ethernet0/0/1
port link-type access
port default vlan 2
#
interface Ethernet0/0/2
port link-type access
port default vlan 4
#
interface Ethernet0/0/3
#
interface Ethernet0/0/4
#
interface Ethernet0/0/5
#
interface Ethernet0/0/6
#
interface Ethernet0/0/7
#
interface Ethernet0/0/8
#
interface Ethernet0/0/9
#
interface Ethernet0/0/10
#
interface Ethernet0/0/11
#
interface Ethernet0/0/12
#
interface Ethernet0/0/13
#
interface Ethernet0/0/14
#
interface Ethernet0/0/15
#
interface Ethernet0/0/16
#
interface Ethernet0/0/17
#
interface Ethernet0/0/18
#
interface Ethernet0/0/19
#
interface Ethernet0/0/20
#
interface Ethernet0/0/21
#
interface Ethernet0/0/22
#
interface GigabitEthernet0/0/1
port link-type trunk
port trunk allow-pass vlan 2 to 4094
#
interface GigabitEthernet0/0/2
port link-type trunk
port trunk allow-pass vlan 2 to 4094
#
interface NULL0
#
user-interface con 0
user-interface vty 0 4
#
return
<JR01>
5、JR02（接入交換機02的配置）
<JR02>dis cu
#
sysname JR02
#
undo info-center enable
#
vlan batch 2 to 5
#
cluster enable
ntdp enable
ndp enable
#
drop illegal-mac alarm
#
dhcp server database enable
#
diffserv domain default
#
drop-profile default
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password simple admin
local-user admin service-type http
#
interface Vlanif1
#
interface MEth0/0/1
#
interface Ethernet0/0/1
port link-type access
port default vlan 5
#
interface Ethernet0/0/2
port link-type access
port default vlan 3
#
interface Ethernet0/0/3
#
interface Ethernet0/0/4
#
interface Ethernet0/0/5
#
interface Ethernet0/0/6
#
interface Ethernet0/0/7
#
interface Ethernet0/0/8
#
interface Ethernet0/0/9
#
interface Ethernet0/0/10
#
interface Ethernet0/0/11
#
interface Ethernet0/0/12
#
interface Ethernet0/0/13
#
interface Ethernet0/0/14
#
interface Ethernet0/0/15
#
interface Ethernet0/0/16
#
interface Ethernet0/0/17
#
interface Ethernet0/0/18
#
interface Ethernet0/0/19
#
interface Ethernet0/0/20
#
interface Ethernet0/0/21
#
interface Ethernet0/0/22
#
interface GigabitEthernet0/0/1
port link-type trunk
port trunk allow-pass vlan 2 to 4094
#
interface GigabitEthernet0/0/2
port link-type trunk
port trunk allow-pass vlan 2 to 4094
#
interface NULL0
#
user-interface con 0
user-interface vty 0 4
#
return
G. 華為匯聚交換機vrrp配置，請高手看看配置有什麼問題嗎
感覺你的vlan 2沒通
兩台交換機之間的互聯鏈路上，配置了vlan 2沒有。vlan 1是默認一定有的，如果你沒配過，那隻通vlan 1就可以解釋了。
H. 華為VRRP配置，具體要怎麼配置呢
lsw5上配置了優先順序，在lsw6上沒有收到，明顯是lsw6就沒有收到來自lsw5的vrrp協議報文，由於協議報文是自動發送，所以你在2台交換機上配置都vlanif口的ip地址不通，導致他們2個都認為自己是master。解決辦法是在交換機上運行路由協議，比方說ospf，isis把要互訪的ip發布出去，或者手寫靜態路由，互指下一跳。